Model 611

Options

Accessories

Curved Profile type C-187 for doors up to 15’4” wide also available in: 20, 18 ga. galvanized steel; 22, 20 ga. stainless steel; 18 ga. (.040”) aluminum
Curved Profile type C-275 for doors up to 20’ wide also available in: 20, 18 ga. galvanized steel; 22, 20 ga. stainless steel; 16 gauge (.050”) aluminum
Flat Profile type F-265 for doors up to 20’ wide also available in: 20, 18 ga. galvanized steel; 22, 20 ga. stainless steel; 16 gauge (.050”) aluminum
Bottom Bar also available in: galvanized steel, stainless steel, aluminum
Wear strips are an available option. (20PSF wind load rating is no longer available when wear strips are selected.)
Guide options include galvanized steel and powdercoated steel
Hood also available in: powdercoat, stainless steel and aluminum
Brackets also available in: powdercoat, and galvanized steel
Direct drive motors available in 1 HP, 2 HP, 3 HP, and 220 VAC 1-phase and 208/230/460/575 VAC 3-phase
Dual photoelectric sensors available for safety
Optional push buttons, loop detectors, radio control, motion detectors or any combination thereof available for door operation/control
PowderGuard® Max powder coat finish options are available in approximately 200 colors as well as custom matching to specification. On the RapidSlat® models PowderGuard® Max is required on curtain to maintain warranty on finish
PowderGuard® Textured powdercoat: Industrial textured powdercoat provides a thicker, more scratch resistant coat for added product protection available on brackets, guides and bottom bar
Fenestrated 18 ga. steel slats or vision lites with uniformly spaced openings of 3" x 5/8" (76 mm x 16 mm) either slat profile or 10” x 1” (254 mm x 25.4 mm) flat slat profile only
Perforated 18 ga. steel slats with 1/16" diameter perforation; spaced 3/32” on center
High wind load options available

‍

Colours

Actual door color may vary from the digital representation shown here.

Color samples are available by request.

Powder Coat Color Options

PowderGuard® Max powder coat options are available in approximately 200 colors as well as custom matching to specification. On the RapidSlat® PowderGuard® Max is required to maintain warranty on finish.

PowderGuard® Max formula is four times harder than our PowderGuard® Premium, providing ehanced strength and durability to the finish and performs well in high cycle applications. Finish also provides easy to clean surface. Available in white, tan, and gray or select a color from approximately 200 RAL powder coat colors.

Features

STANDARD MAX WIDTH:

up to 20' (6096 mm) depending on gauge and slat type

STANDARD MAX HEIGHT:

up to 20' (6096 mm) depending on gauge and slat type

MOUNTING:

Interior or exterior face of wall

WIND LOAD:

20 psf when optional wear strips are not specified

DOOR ROLL:

Direct driven, springless roll with integrated shafts; self-aligning grease-able sealed bearings; door does not require counterbalance device

GUIDES:

Three structural steel angles PowderGuard® Premium powder coated black

CURTAIN FINISH:

Gray, tan or white PowderGuard® Max powder coat with hardening additive

ACTUATOR:

Single open/close/stop push button station incorporated into control panel

CURTAIN:

Interlocking roll-formed slats, end locks attached to prevent lateral movement; Curved profile type C-187 for doors up to 15'4" wide; 22 gauge galvanized steel; Curved profile type C-275 for doors up to 20' wide; 22 gauge galvanized steel; Flat profile type F-265 for doors up to 20' wide; 22 gauge galvanized steel

CONTROL PANEL:

Variable frequency drive controller with self-diagnostics (time delay self-close timer and non-resettable cycle counter included); LCD readout, enclosure NEMA 4X rated

OPERATION:

Direct drive, integrated gear motor/brake assembly (up to 24” per sec up speed / 12” per sec down speed); drive assembly and limit sensors are factory pre-assembled; manual hand chain for power outage